Laboratory Incubators

TECHNICAL DATA

Laboratory Incubators Specifications & Technical Documentation

Select a product to view its specifications, available options and technical documents.

Find a product

Laboratory Incubators

Plant Growth Chamber

View Product

Brand / manufacturer: BINDER / Ningbo Jiangnan
Series: KB PRO + LED / RXZ
Lighting: RXZ: two- or three-side fluorescent up to 30,000 lx; BINDER: 16 movable LED bars with three channels
Temperature Range: 0–50 °C (RXZ); −10 to 60 °C with the LED module fitted (BINDER)
Humidity: 50–95 %RH on RXZ; humidity control requires the KBF range on BINDER
Documentation: Model-specific capacities and temperature bands are listed for each configuration; final electrical supply, documentation and pricing are confirmed by quotation.
Available configurations: RXZ-160 · 160 L (chamber 540 × 540 × 650 mm); KB PRO 720 + LED · 727 L (chamber 1011 × 575 × 1250 mm)
Configuration: RXZ-160 · 160 L (chamber 540 × 540 × 650 mm) · KB PRO 720 + LED · 727 L (chamber 1011 × 575 × 1250 mm)

APPLICATIONS

Laboratory Incubators Applications & Use Cases

Application-led selection for real laboratory workflows.

Start from the organism, not the cabinet size

An incubator is only correctly specified once the organism, the working temperature, the acceptable drift and the atmosphere are fixed. A 165 L chamber and a 165 L chamber with CO2 control are different products with different contamination risks and different running costs.

Match the heat-transfer and cooling principle

Direct-heat and air-jacketed chambers recover quickly and are simple to service. Water jackets hold temperature through short power interruptions but add weight and maintenance. Compressor cooling reaches below ambient; Peltier cooling removes the refrigerant and the vibration at the cost of a narrower band and a smaller cabinet.

Treat contamination control as a specification, not an accessory

Sterilisation method, chamber material, HEPA filtration on CO2 units and condensate handling determine how often the chamber has to be taken out of service. A 180 °C dry-heat cycle, a UV lamp and a 90 °C humid cycle are not interchangeable claims.

Plan the room, the power and the documentation

Incubators fail commissioning for mundane reasons: no clearance for the door swing, a circuit that cannot carry the compressor start current, or a chamber that cannot be moved through the corridor. Regulated work also needs calibration certificates and a qualification pack that arrives with the unit.

PERFORMANCE & SELECTION

Start from the organism, not the cabinet size

An incubator is only correctly specified once the organism, the working temperature, the acceptable drift and the atmosphere are fixed. A 165 L chamber and a 165 L chamber with CO2 control are different products with different contamination risks and different running costs.

State the organism and the target temperature, including any cold-side requirement below ambient
Decide whether the work needs CO2, reduced O2, elevated humidity or agitation before comparing volumes
Check that the uniformity figure is quoted at your working temperature, not only at 37 °C

Start from the organism, not the cabinet size

CONFIGURATION & COMPATIBILITY

Match the heat-transfer and cooling principle

Direct-heat and air-jacketed chambers recover quickly and are simple to service. Water jackets hold temperature through short power interruptions but add weight and maintenance. Compressor cooling reaches below ambient; Peltier cooling removes the refrigerant and the vibration at the cost of a narrower band and a smaller cabinet.

Choose a water jacket when temperature hold-through matters more than weight
Choose Peltier when vibration or refrigerant restrictions rule out a compressor
Confirm that the published band is achievable at your ambient temperature, not only in a conditioned room

Match the heat-transfer and cooling principle

IDENTIFICATION & TRACEABILITY

Clear Product Identification & Specification

Product names, model numbers, SKUs and option identifiers keep quotations, orders and internal records aligned.

Product and model identification
Option-specific SKU information
Consistent quotation specifications

PRODUCT IDENTIFICATIONLaboratory Incubators

Catalog: Laboratory equipment
Products: 25
Selection: Specification-led

QUALITY RECORDS

Traceable Supply & Quality Inspection

Documentation and inspection requirements are confirmed against the selected product and order.

Product identification records
Pre-delivery checks
Documents available on request

QUALITY STANDARDS

Choose the Right Laboratory Incubators Specification

Compare the specifications that determine application fit and acceptance.

G—01